AirLink AWLL6086 Bedienungshandbuch

Wireless N 300 Mini USB Adapter Model # AWLL6086 User’s Manual Rev. 1.0

9 Step 3.4 Select Install or choose your install destination through Customize. Step 3.3 Press Continue to begin installation.

10 Step 3.3 After installation is complete, Restart your computer to begin using the Wireless Utility. 4. Connect to the Wireless Network Thi

11 Step 4.1 Click on the wireless icon in the system tray at the bottom right-hand corner of your screen. A list of available network will pop up. S

12 For All Windows Users: Step 4.1 After rebooting the computer, open Airlink101 Wireless Monitor utility by double clicking on the Airlink101 Wire

13 Step 4.3 Enter the wireless security key into the Network Key box if the network you are attempting to connect has wireless security enabled. Cl

14 Congratulations! You have now connected to the wireless network successfully. Troubleshooting 1. If you cannot open the wireless monitor uti

15 5. Configure Wireless Monitor This section describes the various functions of the Airlink101 Wireless Monitor that you can configure, including

16 Note: Virtual WiFi allowed is not supported in this utility version. 5.2 Profile Settings The Profile tab lists the current profiles and allow

17 Enter a Profile Name and SSID. Enter the encryption settings for the profile. Click OK to save the changes. To remove an existing profile, s

18 5.3 Available Network The Available network tab lists all of the networks that the adapter detects in your area. Clicking Refresh will refresh

1 Table of Contents 1. Introduction ...

19 5.4 Status The status section provides you with a list of information about the current status of the adapter.

20 5.5 Wi-Fi Protected Setup (WPS) The Wi-Fi Protected Setup™ (WPS) is a new and easy way to configure the encryption for your wireless network cli

21 - For Push Button method, click Push Button Config (PBC) tab, continue to Step 5.6.2a - For Pin Input Config method, click Pin Input Config (PIN)

22 Select the Access Point that you want to connect, and then click Select.

23 Step 5.5.3b Log on to your router’s configuration page from the web browser and click on Wireless. Then enter the WPS settings. Step 5.5.3c

24 After a few moments both the router configuration screen and the adapter configuration screen should show a message telling you that a connec

25 5.6 Configuring Wireless Security This section describes the different types of encryption available and how to configure them. In most cases, e

26 WPA/WPA2-PSK: The most secure and recommended level of encryption

27 5.6.1 Configuring WEP encryption Select WEP from the Data encryption box. Under Network Authentication, you will want to select Shared key

28 5.6.2 Configuring WPA/WPA2-PSK Encryption (for home users) Select WPA-PSK/WPA2-PSK from the Network Authentication box. Under Data encrypti

2 1. Introduction Congratulations on your purchase of the Wireless N 300 Mini USB Adapter. The compact design gives you more flexibility and its hi

29 5.6.3 Configuring WPA/WPA2 Encryption (for corporate networks) Select WPA 802.1x / WPA2 802.1x from the Network Authentication box. Under Dat

30 5.7 Ad-hoc and Peer-to-Peer Wireless Networks Ad-hoc networking is used when you want to connect two or more computers together but you don’t ha

31 You can also choose between no security or WEP security. If you choose WEP security, you can follow the instructions in the Configuring Encryptio

32 make sure that you do this on every ad-hoc machine so that they will all be set to the same channel. 5.8 About The About window provides the

33 Appendix A - Specification Frequency Band • 2.4Ghz Standards • IEEE 802.11b / g / n Interface • USB 2.0 / 1.1 Data Rate* • Receiving: 300M

34 Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Theo

3 2. Install the Wireless Adapter This section provides instructions on how to install the Wireless N 300 Mini USB Adapter. Step 2.1 Insert the U

4 Step 2.3 Insert the Installation CD in the CD drive. Note: If the Autorun screen doesn’t appear automatically, go to My Computer, double click y

5 Step 2.6 Give Permission to Window to install the driver software. Windows 7 / Vista Users: Click the Install this driver software anyway. Wi

6 You will see the following message when it is installing the driver for Airlink101 Wireless Adapter and the Airlink101 Wireless Monitor. Step

7 The driver and utility have been installed successfully. Please continue to the next chapter. 3. Install the Driver/Utility on Mac OSX This se

8 Step 3.3 Choose you preferred language and press Continue to view the License Agreement. After review, press Agree to continue.